Menu
Your Cart

ST-LINK/V2 (CN) - STM8 / STM32 Programmer & Debugger

ST-LINK/V2 (CN) - STM8 / STM32 Programmer & Debugger
ST-LINK/V2 (CN) - STM8 / STM32 Programmer & Debugger
ST-LINK/V2 (CN) - STM8 / STM32 Programmer & Debugger
ST-LINK/V2 (CN) - STM8 / STM32 Programmer & Debugger
ST-LINK/V2 (CN) - STM8 / STM32 Programmer & Debugger
ST-LINK/V2 (CN) - STM8 / STM32 Programmer & Debugger
ST-LINK/V2 (CN) - STM8 / STM32 Programmer & Debugger
ST-LINK/V2 (CN) - STM8 / STM32 Programmer & Debugger
Made in China
ST-LINK/V2 (CN) - STM8 / STM32 Programmer & Debugger
₹​1,414.82
₹​1,199.00 + 18% GST
All Inclusive, Shipping Calculated at Checkout

B2B GST Credit Available

ST-LINK/V2 (CN) - STM8 / STM32 Programmer & Debugger

The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.

  • STM8 applications use the USB full speed interface to communicate with STMicroelectronic's ST Visual Develop (STVD) or ST Visual Program (STVP) software.
  • STM32 applications use the USB full speed interface to communicate with Atollic, IAR, Keil or TASKING integrated development environments.

Features

  • 5 V power supplied by a USB connector
  • USB 2.0 full speed compatible interface
  • USB standard A to mini B cable
  • SWIM specific features
  • 1.65 V to 5.5 V application voltage supported on SWIM interface
  • SWIM low-speed and high-speed modes supported
  • SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed
  • SWIM cable for connection to the application via an ERNI standard vertical (ref: 284697 or 214017) or horizontal (ref: 214012) connector
  • SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector
  • JTAG specific features
    • 1.65 V to 3.6 V application voltage supported on the JTAG interface and 5 V tolerant inputs
    • JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector
  • Direct firmware update feature supported (DFU)
  • Status LED which blinks during communication with the PC
  • Operating temperature 0 to 50 °C

 


Device Drivers

While connecting the ST-LINK/V2 to the computer through USB interface, the USB driver is required and should be installed correctly first.

Click on the link below to download:

ST-LINK/V2 USB driver for Windows 7, Vista and XP


ST Link LED status

The LED labeled 'COM' on top of the ST-LINK/V2 shows the ST-LINK/V2 status (whatever the connection type). When the:

  • LED is blinking RED: the first USB enumeration with the PC is taking place. If it keeps blinking RED, maybe the USB driver is NOT found.
  • LED is RED: communication between ST-LINK/V2 and the PC is established (end of enumeration).
  • LED is blinking GREEN/RED: data are being exchanged between the target and the PC.
  • LED is GREEN: the last communication has been successful.
  • LED is ORANGE: ST-LINK/V2 communication with the target has failed.

 

Write a review

Note: HTML is not translated!
Bad Good
Captcha