









This product qualifies for Free Surface Shipping !
B2B GST Credit Available
- Stock: 0 in Stock
- SKU: 09148
- Delivery Time
- Bulk & B2B RFQ
Adafruit VL53L5CX Time-of-Flight Distance 8x8 Pixel Camera - STEMMA QT / Qwiic
The Adafruit VL53L5CX Time of Flight Sensor takes the great Time of Flight distance sensor technology we've seen from ST in the VL5 series of chips, and gives you a full grid of 8x8 sensor squares. This means we don't just measure up to 4 meters away, you also get to divide the measurement cone into 64 spots and get the individual distance for each. This makes it more like a depth camera than a sensor, albeit not a very high resolution one.
The sensor contains a very tiny invisible laser source, a fixed 8x8 diffractive optic lens, and 64 matching sensors. The VL53L5CX can detect the "time of flight", or how long the light has taken to bounce back to the sensors. The optics and laser are tuned and narrow so you get nice and crisp measurements from each grid point. Unlike sonars that bounce ultrasonic waves, the 'cone' of sensing is very narrow. Unlike IR distance sensors that try to measure the amount of light bounced, the VL53 is much more precise and doesn't have linearity problems or 'double imaging' where you can't tell if an object is very far or very close.
The earlier series of VL53 sensors (VL53L0, VL53L1, VL53L3, and VL53L4) have a variety of ranges and field-of-view but only do one zone. This one does way more, and you have to load in the firmware so you definitely cannot use 'small memory' boards like the ATmega328 - you'll need a SAMD21, SAMD51, ESP, etc chip with more than 128K of flash memory and over 16K of SRAM! It also takes longer to start up than simpler ToF sensors, about 3 seconds cold-boot, since you have to load in that firmware.
However, as long as you have a big-enough chip, the sensor is small and easy to use in any robotics or interactive project. As it needs 3.3V power and logic we put the little fellow on a breakout board with a regulator and level shifting. You can use it with any 3-5V power or logic microcontroller with no worries. Works great with the 3.3V logic level of a Feather, or the 5v level of a Arduino Mega, this breakout is ready to work with most common microcontrollers or SBCs. and since it speaks I2C, you can easily connect it up with two data wires plus power and ground.
Specifications
- Fast and accurate multi zone distance ranging sensor
- Multi zone ranging output with either 4x4 or 8x8 separate zones
- Autonomous low-power mode with interrupt programmable threshold to wake up the host
- Up to 400 cm ranging
- Multi target detection and distance measurement in each zone
- 60 Hz frame rate capability
- Histogram processing, and algorithmic compensation minimizes or removes the impact of cover glass crosstalk
- Motion indicator for each zone to show if targets have moved and how they have moved
- Emitter: 940 nm invisible light vertical-cavity surface-emitting laser (VCSEL) and integrated analog driver
- 65° diagonal square FoV using diffractive optical elements (DOE) on both transmitter and receiver
- Receiving array of single photon avalanche diodes (SPADs)
- Low-power microcontroller running firmware
- Compatible with a wide range of cover glass materials
- Optical Sensor 157.480" (4m) I2C Output
- Product Dimensions: 25.4mm x 17.7mm x 4.6mm / 1.0" x 0.7" x 0.2"
- Product Weight: 1.9g / 0.1oz
Package Includes
- 1x Adafruit VL53L5CX Time-of-Flight Distance 8x8 Pixel Camera - STEMMA QT / Qwiic
Warranty Terms :
Branded products (Waveshare/ Raspberry Pi/ Radxa/ DWIN etc) are as per brand warranty terms. Generic products are eligible for replacement within 7 days of delivery based on following conditions.
Products are eligible for a replacement if there is physical damage during transit or a clear manufacturing defect. Any claim for damage/ wrong items/ short quantity/ replacement must be made within 48 hours of successful delivery of the product. Requests for refund of amount or exchange of product(s) will be reviewed on a case by case basis and HUBTRONICS carries final rights to take a final decision on refund, store credit or exchange.
Unboxing video is mandatory to report damaged or short quantity of the items in the order.
What to take care of ?
Most of our products are technical in nature and require trained personnel to handle them. Any kind of mishandling can result in damage or malfunctioning of the product, it is not possible for us to provide a replacement or refund if the product is damaged due to technical or physical mishandling.
Who pays the return shipping cost?
Free of cost return pickup from delivery address is eligible for products categorized as manufacturing defect/ Damage in transit/ Wrong items delivered. We do not support return pickup for any B2B order or offline orders not placed on website. Buyer need to arrange return shipping for B2B orders.
What voids warranty?
Please note that replacement/ return or refund is not possible if the product is not compatible with your system/application. Please check all the technical details/ dimensions etc. before ordering and contact us for any kind of clarifications.
If product is soldered/ programmed at any point or physically altered in any way, it is not eligible for return/ replacement. If the item requires soldering for testing, please ensure that you use suitable clips or jig to test it without soldering. Any kind of soldering job makes the product ineligible for return or replacement.
Following items are not eligible for return under any circumstances
- Device Programmers / Dongles
- Soldering Consumables (Wire, Flux etc)




