B2B GST Credit Available
- Stock: 0 in Stock
- SKU: 21606
- Delivery Time
- Bulk & B2B RFQ
7inch Touch Screen All-In-One Kit Designed for Raspberry Pi CM4, 5MP Camera, Aluminum Case
This is a 7-inch touch screen all-in-one kit designed for Raspberry Pi CM4. CM4-DISP-BASE-7A-BOX supports POE power supply and 7~36V DC power supply, Onboard four-way USB2.0, 7-inch touch screen, etc., the all-in-one kit is convenient for use.
User Manual / Datasheet / Example Codes Etc.
Specifications
- CM4 SOCKET : suitable for all variants of Compute Module 4
- NETWORKING : Gigabit Ethernet RJ45 , M.2 M KEY, supports NVME SSD
- USB : USB 2.0 × 4
- CONNECTOR : isolated RS485, RS232, GPIO, and I2C
- DISPLAY : 7inch, 800 × 480 pixels, 5-points capacitive touch, toughened glass panel
- CAMERA : 5MP, F2.4, 3.89mm fixed focal length, supports video recording
- VIDEO : HDMI, supports 4K 30fps output
- RTC : Real-time clock with battery socket and ability to wake Compute Module 4
- STORAGE : MicroSD card socket for Compute Module 4 Lite (without eMMC) variants
- FAN : 5V/12V, allows speed adjustment and measurement
- SPEAKER : 8Ω 2W dual track speakers
- POWER INPUT : 7-36V
- DIMENSIONS : 196.68 × 114.42mm
Package Includes
- 1x All-in-one kit
- 1x 12V 2A power adapter
- 1x Screwdriver
5MP Front Camera
Design Details
Rich Interfaces
Providing Interfaces Including: CSI, HDMI, USB, M.2, ETH, RS232, RS485
What's On Board
1. CM4 Connector : suitable for all variants of Compute Module 4
2. DC power supply interface : 7~36V DC wide voltage power supply, it is recommended to use a 24W or higher power supply
3. CM4 Status Indicator : PWR: Raspberry Pi Power Indicator ACT: Raspberry Pi Working Status Indicator
4. HDMI port : Support 4K 30fps output
5. RJ45 Gigabit Ethernet port : Support 10 / 100 / 1000M network access
6. USB2.0 interface : 4x USB 2.0, for connecting sorts of USB devices
7. Micro SD card interface : for connecting a Micro SD card with a pre-burnt image (Lite variant ONLY)
8. USB SLAVE port : USB programming port
9. BOOT switch button : ON: CM4 will be booted from USB-C interface OFF: CM4 will be booted from eMMC or Micro SD card
10. MIPI CSI interface : connected to the 5MP front camera
11. Isolated I2C : for controlling or reading data from devices via I2C
12. Isolated GPIO : for controlling or detecting devices via GPIO
13. Isolated RS485 : can communicate through the RS485 interface
14. Isolated RS232 : can communicate through the RS232 interface
15. DC power supply : 7 ~ 36V DC power supply interface
16. RS485 termination resistor and GPIO logic level selection : RS485: connect/disconnect the 120R resistor GPIO: GPIO logic level selection
17. RTC Battery Connector : supports CR1220 button cell
18. Touch screen interface : connected to the capacitive touch screen
19. Display connector : connected to the 7inch 800×480 display
20. M.2 M KEY : supports M.2 M KEY NVME SSD, or other communication modules using PCIe channel
21. Speaker interface : audio output
22. FAN : for connecting the cooling fan, allows speed adjustment and measurement
23. RTC Interrupt Pin Switch : GL-EN: CM4 power down on RTC interruption, PI-RUN: CM4 will reboot on RTC interruption, D16: D16 pin is triggered on RTC interruption (default)
24. System function switch : BT_DIS: Bluetooth disabled, for CM4 with antenna variant ONLY, WIFi_DIS: WiFi disabled, for CM4 with antenna variant ONLY, WP_DIS: the boot mode switch, ONLY be used when NOT booted from eMMC or SD card
25. FAN Power Supply Selection : select 5V (default) or 12V power to drive the fan
26. IO-VREF selection : set the CM4 IO logic level as 3.3V (default) or 1.8V
27. RS485 toggle : GPIO13/12: using ttyAMA1 device (default), GPIO15/14: use ttyS0 device
28. I2C bus selection of RTC/FAN : SDA0/SCL0: I2C-10 is shared with CSI/DSI, GPIO3/2: I2C-1 is shared with 40PIN GPIO (default)
Dimensions