Menu
Your Cart

13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi, SPI interface

13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi, SPI interface
13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi, SPI interface
13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi, SPI interface
13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi, SPI interface
13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi, SPI interface
13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi, SPI interface
13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi, SPI interface
13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi, SPI interface
WaveShare Electronics
13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi, SPI interface
₹​15,798.00
₹​13,388.14 + 18% GST
All Inclusive, Shipping Calculated at Checkout
Assured Cashback of ₹ 134
B2B GST Credit Available
Price in reward points: 13388

13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi, SPI interface

This is an 13.3inch 960x680 E-Ink display HAT (K) for Raspberry Pi. The E-Ink Raw display comesSPI interface, for connecting with controller boards like Raspberry Pi/Jetson Nano/Arduino/STM32, etc.


User Manual / Datasheet / Example Codes Etc.


Features

  • No backlight, keeps displaying last content for a long time even when power down
  • Ultra low power consumption, basically power is only required for refreshing
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
  • SPI interface, for connecting with controller boards like Raspberry Pi/Jetson Nano/Arduino/STM32, etc.
  • Onboard voltage translator, compatible with 3.3V / 5V MCUs
  • Comes with online development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32)


Specifications

  • OPERATING VOLTAGE : 3.3V/5V
  • DISPLAY COLOR : black, white
  • INTERFACE : 3-wire SPI, 4-wire SPI
  • GREY SCALE : 2
  • OUTLINE DIMENSIONS : 286.32 × 212.26mm
  • FULL REFRESH TIME : 5s
  • DISPLAY SIZE : 275.52 × 195.16mm
  • REFRESH POWER :  66mW
  • DOT PITCH : 0.287 × 0.287mm
  • STANDBY CURRENT : <0.01uA (almost none)
  • RESOLUTION : 960 × 680 pixels
  • VIEWING ANGLE : >170°


Package Includes 

  • 13.3inch e-Paper (K) x1
  • e-Paper Driver HAT x1
  • RPi screws pack (2pcs) x1
  • GH1.25 9PIN cable ~20cm x1



13.3" E-PAPER HAT (K)

Low Power Consumption, Wide Viewing Angle, Paper-Like Displaying Without Electricity


Onboard SPI Control Interface

For Use With Other Controller Boards Like Raspberry Pi/Jetson Nano/STM32/Arduino


  • VCC : 3.3V/5V
  • GND : Ground
  • DIN : SPI MOSI pin
  • CLK : SPI SCK pin
  • CS : SPI chip selection, low active
  • DC : Data / Command selection (high for data, low for command)
  • RST : External reset, low active
  • BUSY : Busy status output
  • PWR : Power on/off control



Standard Raspberry Pi 40PIN GPIO Header

Compatible With Raspberry Pi Series Boards, Jetson Nano




Application Examples




Dimensions


Write a review

Note: HTML is not translated!
Bad Good
Captcha