Menu
Your Cart

We are not operational yet. This site is currently under construction. Please check back after a while. For any queries, write to us at [email protected] 

Arduino Nano v3.0 Clone

Arduino Nano v3.0 Clone
Arduino Nano v3.0 Clone
Arduino Nano v3.0 Clone
Arduino Nano v3.0 Clone
Arduino Nano v3.0 Clone
Arduino Nano v3.0 Clone
Arduino Nano v3.0 Clone
Arduino Nano v3.0 Clone
Arduino Nano v3.0 Clone
₹​ 352.82
Ex Tax: ₹​ 299.00
ex. GST
  • Stock: In Stock
  • SKU: R-1412
  • Weight: 25.00g
  • B2B GST Credit Available
  • Delivery Time
  • RFQ

Arduino Nano v3.0 Clone without Cable

Overview :
The Arduino Nano v3.0 clone is a small, complete, and breadboard-friendly board based on the ATmega328 . It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one.

Specifications : 

Microcontroller Atmel  ATmega328
Operating Voltage (logic level) 5 V
Input Voltage (recommended) 7-12 V
Input Voltage (limits) 6-20 V
Digital I/O Pins 14 (of which 6 provide PWM output)
Analog Input Pins 8
DC Current per I/O Pin 40 mA
Flash Memory 32 KB (ATmega328) of which 2 KB used by bootloader
SRAM 2 KB (ATmega328)
EEPROM 1 KB (ATmega328)
Clock Speed 16 MHz
Dimensions 0.73" x 1.70"

Power : 
The Arduino Nano can be powered via the Mini-B USB connection, 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.The FTDI FT232RL chip on the Nano is only powered if the board is being powered over USB. As a result, when running on external (non-USB) power, the 3.3V output (which is supplied by the FTDI chip) is not available and the RX and TXLEDs will flicker if digital pins 0 or 1 are high.

Memory : 

The ATmega328has 32 KB, (of which 2 KB used for the bootloader). The ATmega328 has 2 KB of SRAM and 1 KB of EEPROM (which can be read and written with the EEPROM Library).

Input and Output : 

Each of the 14 digital pins on the Nano can be used as an input or output, using pinMode()digitalWrite(), anddigitalRead() functions. They operate at 5 volts. Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. In addition, some pins have specialized functions:

  • Serial: 0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL serial data. These pins are connected to the corresponding pins of the FTDI USB-to-TTL Serial chip.
  • External Interrupts: 2 and 3. These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt() function for details.
  • PWM: 3, 5, 6, 9, 10, and 11. Provide 8-bit PWM output with the analogWrite() function.
  • SPI: 10 (SS), 11 (MOSI), 12 (MISO), 13 (SCK). These pins support SPI communication, which, although provided by the underlying hardware, is not currently included in the Arduino language.
  • LED: 13. There is a built-in LED connected to digital pin 13. When the pin is HIGH value, the LED is on, when the pin is LOW, it's off.
     

The Nano has 8 analog inputs, each of which provide 10 bits of resolution (i.e. 1024 different values). By default they measure from ground to 5 volts, though is it possible to change the upper end of their range using theanalogReference() function. Analog pins 6 and 7 cannot be used as digital pins.
There are a couple of other pins on the board:

  • AREF. Reference voltage for the analog inputs. Used with analogReference().
  • Reset. Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields which block the one on the board.
  •  
  • Programming :

The Arduino Nano can be programmed with the Arduino software (download). Select "Nano w/ ATmega328" from the Tools > Board menu (according to the microcontroller on your board).

The ATmega168 or ATmega328 on the Arduino Nano comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol 
 


ask a question about this product

Write a review

Please login or register to review

Q. Do you provide Cash on Delivery service?
A. We do not support Cash on delivery. we understand that some of the customers may feel it unsafe to transact on hubtronics website. We assure that your transactions are 100% secured. Major reasons for us not supporting CoD are following.

  • We are not a marketplace platform, we are a single seller webstore. Marketplaces like Amazon and Flipkart have to provide services like CoD to ensure that the customers are safe from the fraudulent sellers. For your order on Hubtronics, we are solely responsible for fulfillment and we make sure that we provide up to the mark service to our customers.
  • We use 3rd party courier services. Unlike Amazon / Flipkart, we can not have our own logistics network and we rely on 3rd party courier services like FedEx, DTDC to deliver your orders. These courier companies charge a good commission amount for CoD orders. The fees charged by courier companies for CoD usually ranges from Rs. 50-80 for each order which makes shipping too costly for small items of values under Rs. 1000. Instead of giving that commission to courier companies, We rather give that price benefit to our customers, who believe in our services.
  • To avoid non-serious customers. We started providing CoD services briefly once. Our experience was quite bad as many people just placed the orders for products they were not actually interested to purchase and they refused to take the delivery. In such cases the parcel is sent back to us by shipping service and we still have to pay courier charges. As we were getting too many such orders, we decided to put a stop to CoD orders.
  • Business is mutual trust. As we are a single seller online store, we understand the consequences of poor quality service. We can not afford to loose your trust. So, give us a chance to gain your trust. #KeepExperimenting!