Menu
Your Cart

Core103R, STM32F1 Core Board

Core103R, STM32F1 Core Board
Core103R, STM32F1 Core Board
Core103R, STM32F1 Core Board
Core103R, STM32F1 Core Board
Core103R, STM32F1 Core Board
Core103R, STM32F1 Core Board
WaveShare Electronics
Core103R, STM32F1 Core Board
₹​2,240.82
₹​1,899.00 + 18% GST
All Inclusive, Shipping Calculated at Checkout
Assured Cashback of ₹ 19
B2B GST Credit Available

Core103R is an STM32 MCU core board designed for STM32F103RCT6, supports further expansion. It is ideal for starting application development with STM32F family.


Features

  • Minimal ready-to-run system, integrates clock circuit, USB control circuit, USB connector, etc.
  • All the I/O ports are accessible on the pin headers
  • JTAG/SWD programming/debugging interface
  • 2.54mm header pitch, allowed to be plugged-in your application board


Resources

User Manual


Onboard Peripherals


  1. STM32F103RCT6:the high performance STM32 MCU which features:
    • Core: Cortex-M3 32-bit RISC
    • Operating Frequency: 72MHz, 1.25 DMIPS/MHz
    • Operating Voltage: 2-3.6V
    • Package: LQFP64
    • Memories: 256kB Flash, 48kB SRAM
    • MCU communication Interfaces:
      • 3xSPI, 5xUSART, 2xI2S, 2xI2C, 1xSDIO, 1xUSB, 1xCAN
    • AD & DA converters: 3 x AD (12-bit, shares 16 channels); 2 x DA (12-bit)
    • Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
  2. AMS1117-3.3: 3.3V voltage regulator
  3. Power supply switch, powered from 5Vin or USB connection
  4. Boot mode selection, for configuring BOOT0 pin
  5. Power indicator
  6. VBUS LED
  7. Reset button
  8. 8M crystal
  9. 32.768K crystal, for internal RTC with calibration
  10. JTAG/SWD interface: for debugging/programming
  11. USB connector, used for establishing USB communication between PC and the STM32 development board
  12. MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion
  13. 5Vin pinheader, 5V power supply input
  14. USB enable jumper
    • short the jumper to enable USB function
    • open the jumper to disconnect from related I/O port
  15. VBAT selection jumper
    • short the jumper to use system power supply
    • open the jumper to connect the VBAT to external power, such as battery

Write a review

Note: HTML is not translated!
Bad Good
Captcha

Warranty Terms : 

Branded products (Waveshare/ Raspberry Pi/ Radxa/ DWIN etc) are as per brand warranty terms. Generic products are eligible for replacement within 7 days of delivery based on following conditions.

Products are eligible for a replacement if there is physical damage during transit or a clear manufacturing defect. Any claim for damage/ wrong items/ replacement must be made within 48 hours of successful delivery of the product. Requests for refund of amount or exchange of product(s) will be reviewed on a case by case basis and HUBTRONICS carries final rights to take a final decision on refund, store credit or exchange.


What to take care of ?

Most of our products are technical in nature and require trained personnel to handle them. Any kind of mishandling can result in damage or malfunctioning of the product, it is not possible for us to provide a replacement or refund if the product is damaged due to technical or physical mishandling.


Who pays the return shipping cost?

Free of cost return pickup from delivery address is eligible for products categorized as manufacturing defect/ Damage in transit/ Wrong items delivered. We do not support return pickup for any B2B order or offline orders not placed on website. Buyer need to arrange return shipping for B2B orders.


What voids warranty? 

Please note that replacement/ return or refund is not possible if the product is not compatible with your system/application. Please check all the technical details/ dimensions etc. before ordering and contact us for any kind of clarifications.

If product is soldered/ programmed at any point or physically altered in any way, it is not eligible for return/ replacement. If the item requires soldering for testing, please ensure that you use suitable clips or jig to test it without soldering. Any kind of soldering job makes the product ineligible for return or replacement. 


Following items are not eligible for return under any circumstances 

  • Device Programmers / Dongles 
  • Soldering Consumables (Wire, Flux etc)