Arduino
₹1,850.00 + 18% GST
B2B GST Credit Available
Arduino UNO R3 Original
1 Pin - Male to Female Jumper Wire - 12 Inch/30.5cm - Pack of 100 PCS Description : These wires are commonly used for prototy..
₹454.30
Ex Gst ₹385.00
1 Pin Female to Female Jumper Wire - 12 Inch - Mixed ColorDescription : These wires are commonly used for prototyping. This&n..
₹9.44
Ex Gst ₹8.00
F-F Jumper Wire - Set of 40 - 2.54mm - 20cm LengthSet of 40 jumper wires with female connector at both ends. Allow you to easily prototype with ..
₹57.82
Ex Gst ₹49.00
F-M Jumper Wire - 20cm Length - 2.54mm - Set of 40Set of 40 jumper wires with female connector at one end and male connector on other. Allo..
₹57.82
Ex Gst ₹49.00
Male to Male Jumper Wires - 1 Pin - Set of 65 Wires - Mix colors - Mix LengthThis is a set of 65 pcs male-to-male high-quality jumper wires cables..
₹93.22
Ex Gst ₹79.00
Male to Male Jumper Wires - 20cm Length - 2.54mm - Set of 40 Set of 40 jumper wires with male connector at both ends. Allow you to..
₹57.82
Ex Gst ₹49.00
2 Pin Shunt - 2.54mm Pitch - Jumper Cap - Yellow ColorPackage Includes : 10x Yellow Jumper Cap 2.54mm
Position
2 Pin
..
₹29.50
Ex Gst ₹25.00
Duracell CR2032 3V Lithium Coin Cell BatteryThe Duracell CR2032 3V Lithium Coin Cell Battery is a reliable and widely used power source for various el..
₹40.00
Ex Gst ₹33.90
400 Tie Points - Solderless BreadboardHigh Quality breadboard with power lanes and printed top face for easy prototyping.Specifications..
₹57.82
Ex Gst ₹49.00₹2,183.00
All Inclusive, Shipping Calculated at Checkout
Assured Cashback of ₹ 14
B2B GST Credit Available
Price in reward points: 1431
- Stock: 2 in Stock
- SKU: 04924
- Delivery Time
- Bulk & B2B RFQ
Arduino Uno Rev3 Original
Arduino Uno is a microcontroller board based on the ATmega328P. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator (CSTCE16M0V53-R0), a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.. You can tinker with your Uno without worrying too much about doing something wrong, worst case scenario you can replace the chip for a few dollars and start over again.
Features
Memory
- AVR CPU at up to 16 MHz
- 32KB Flash
- 2KB SRAM
- 1KB EEPROM
Security
- Power On Reset (POR)
- Brown Out Detection (BOD)
Peripherals
- 2x 8-bit Timer/Counter with a dedicated period register and compare channels
- 1x 16-bit Timer/Counter with a dedicated period register, input capture and compare channels
- 1x USART with fractional baud rate generator and start-of-frame detection
- 1x controller/peripheral Serial Peripheral Interface (SPI)
- 1x Dual mode controller/peripheral I2C
- 1x Analog Comparator (AC) with a scalable reference input
- Watchdog Timer with separate on-chip oscillator
- Six PWM channels
- Interrupt and wake-up on pin change
ATMega16U2 Processor
- 8-bit AVR® RISC-based microcontroller
Memory
- 16 KB ISP Flash
- 512B EEPROM
- 512B SRAM
- debugWIRE interface for on-chip debugging and programming
Specifications
- Microcontroller : ATmega328P
- Operating Voltage : 5V
- Input Voltage (recommended) : 7-12V
- Input Voltage (limit) : 6-20V
- Digital I/O Pins : 14 (of which 6 provide PWM output)
- PWM Digital I/O Pins : 6
- Analog Input Pins : 6
- DC Current per I/O Pin : 20 mA
- DC Current for 3.3V Pin : 50 mA
- Flash Memory : 32 KB (ATmega328P) of which 0.5 KB used by bootloader
- SRAM : 2 KB (ATmega328P)
- EEPROM : 1 KB (ATmega328P)
- Clock Speed : 16 MHz
- LED_BUILTIN : 13
- Length : 68.6 mm
- Width : 53.4 mm
- Weight :25 g
- Package Includes : 1x Ardunio Uno Rev3
Pin Daigram
-1-300x300.jpg "Heltec ESP32-S3 MCU + SX1262 LoRa 868MHz Wireless Stick(V3) Development Board With 0.49inch OLED Display")
