Menu
Your Cart
Our order fulfillment operations will remain suspended on 29th and 30th March 2024 for FY Closing. Any order placed after 2 PM on 28th March will be shipped on 1st April 2024. 

e-Paper IoT Driver HAT for Raspberry Pi, Supports NB-IoT/eMTC/GPRS - SIM7000E

e-Paper IoT Driver HAT for Raspberry Pi, Supports NB-IoT/eMTC/GPRS - SIM7000E
e-Paper IoT Driver HAT for Raspberry Pi, Supports NB-IoT/eMTC/GPRS - SIM7000E
e-Paper IoT Driver HAT for Raspberry Pi, Supports NB-IoT/eMTC/GPRS - SIM7000E
e-Paper IoT Driver HAT for Raspberry Pi, Supports NB-IoT/eMTC/GPRS - SIM7000E
e-Paper IoT Driver HAT for Raspberry Pi, Supports NB-IoT/eMTC/GPRS - SIM7000E
e-Paper IoT Driver HAT for Raspberry Pi, Supports NB-IoT/eMTC/GPRS - SIM7000E
WaveShare Electronics
e-Paper IoT Driver HAT for Raspberry Pi, Supports NB-IoT/eMTC/GPRS - SIM7000E
₹​3,053.84
₹​2,588.00 + 18% GST
All Inclusive, Shipping Calculated at Checkout
Assured Cashback of ₹ 26
B2B GST Credit Available

This is a Raspberry Pi IoT driver board for e-Paper raw panels. It allows getting text/image data from IoT clouds through NB-IoT/eMTC/EDGE/GPRS network connection, and then display them on the e-Paper. Applications includes any scenario where remote refresh of display is required such as shelf display etc.


Package Includes

  • e-Paper NB-IoT/GPRS HAT x1
  • LTE full bands PCB antenna x1
  • e-Paper Adapter x1
  • 24PIN FFC x1
  • 2×20PIN female pinheader x1
  • RPi screws pack (2pcs) x1

Development Resources

Wiki Page  - http://www.waveshare.com/wiki/e-Paper_NB-IoT_GPRS_HAT


  • Onboard SIM7000E module, controlled via UART, supports NB-IoT/eMTC/EDGE/GPRS communication
  • e-Paper interface, controlled via SPI, compatible with various Waveshare SPI e-Paper raw panels
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards
  • Breakout SIM7000E and e-Paper control pins, for connecting with host control boards like STM32
  • 3.7V lithium battery port and charging circuit, provides power to SIM7000E module or external 3.3V system (5V system like Raspberry Pi requires another power supply)
  • Onboard voltage translator, select 3.3V/5V operating voltage by switch
  • Provides Windows host code (based on Alibaba Cloud), make it easy to study/develop, or integrate it into IoT applications
  • Comes with development resources and manual (examples for Raspberry Pi/STM32)

  • Communication interface: UART + SPI (4-wire SPI by default, switch to 3-wire SPI by soldering)
  • Communication module: SIM7000E
  • Quad-Band LTE-FDD B3/B8/B20/B28
  • GPRS/EDGE 900/1800Mhz
  • GNSS (GPS, GLONASS, BeiDou, and Galileo, GNSS antenna is required and NOT included)
  • Support SIM card: NB-IoT specific card, or 1.8V/3V normal SIM card
  • Power supply voltage: 5V
  • Logic level: 5V / 3.3V
  • Applicable battery: 3.7V lithium battery via PH2.0 connector (NOT included)
  • Dimensions: 56.5mm x 65mm

 

Write a review

Note: HTML is not translated!
Bad Good
Captcha