Menu
Your Cart
Our order fulfillment operations will remain suspended on 29th and 30th March 2024 for FY Closing. Any order placed after 2 PM on 28th March will be shipped on 1st April 2024. 

nRF52840 Bluetooth 5.0 Evaluation Kit

nRF52840 Bluetooth 5.0 Evaluation Kit
nRF52840 Bluetooth 5.0 Evaluation Kit
nRF52840 Bluetooth 5.0 Evaluation Kit
nRF52840 Bluetooth 5.0 Evaluation Kit
WaveShare Electronics
nRF52840 Bluetooth 5.0 Evaluation Kit
₹​2,023.70
₹​1,715.00 + 18% GST
All Inclusive, Shipping Calculated at Checkout
Assured Cashback of ₹ 22
B2B GST Credit Available
10 or more ₹​1,976.50

nRF52840 Bluetooth 5.0 Evaluation Kit


NRF52840 Eval Kit is a development/evaluation kit based on nRF52840, features Arduino / Raspberry Pi connectivity, and several common used peripherals.

It supports the new generation Bluetooth 5.0, compared to Bluetooth 4.0, the data rate is twice, up to 2Mbps, the transfer distance is quadruple. Based on the ARM Cortex-M4F architecture, the CPU frequency achieves up to 64MHz. Bluetooth MESH and 2.4GHz radio are also available, that means higher performance, and more suitable applications.

Thanks to the onboard Arduino / Raspberry Pi compatible headers, both Arduino shields and Raspberry Pi HATs can be attached at the same time, make it easy to use more expansion resources.


Features

  • Arduino connectivity, supports Arduino shields
  • Raspberry Pi connectivity, supports Raspberry Pi HATs
  • Integrates CP2102 USB TO UART, for serial debugging
  • Onboard several peripherals and interfaces, convenient for study / development
  • Comes with development resources and manual (examples for Bluetooth 5.0 / Bluetooth MESH)

Development Resources

Wiki : www.waveshare.com/wiki/NRF52840_Eval_Kit


Package Content

  • NRF52840 Eval Kit x1
  • USB type A plug to micro B plug cable x1
  • NFC antenna x1

NRF52840 Eval Kit on board resource

  • 1. Arduino headers: for connecting Arduino shields
  • 2. Raspberry Pi GPIO header: for connecting Raspberry Pi HATs
  • 3. USB TO UART interface
  • 4. USB port: the USB port of nRF52840
  • 5. 4PIN SWD debugging interface: for connecting ARM Debugger to program / debug
  • 6. 3.3V/5V power input/output: provides power output OR powered from external power supply
  • 7. Core52840: nRF52840 core module
  • 8. CP2102: USB TO UART converter
  • 9. Buzzer
  • 10. RT9193-33: 3.3V voltage regulator
  • 11. Optical sensor
  • 12. Keys: RESET and USER KEY
  • 13. LEDs
    • PWR: power indicator
    • RXD/TXD: nRF52840 UART RX/TX indicator
    • LED1~LED4: USER LEDs
  • 14. Power switch
    • USB: powered from USB connection
    • Battery: powered from CR2032 battery
  • 15. NFC antenna connector
  • 16. TF card slot
  • 17. CR2032 battery holder
  • 18. Jumpers
    • Short the jumpers: connect the onboard peripherals to I/Os in example code
    • Open the jumpers: connect to custom I/Os via jumper wires
  • 19. Current testing pads: 0Ω resistor is soldered by default, remove the resistor to test current of the board

 

Write a review

Note: HTML is not translated!
Bad Good
Captcha